17TR Beic Gan Ceramig ffibr carbon Jockey pwli Olwyn Set Derailleurs Cefn Canllaw Olwyn
disgrifiad cynnyrch
* 17T maint mawr system gosod canllaw olwyn
*17T pulleys or16T pulleys
* Mae'n arbed 60% ymwrthedd ffrithiant gadwyn o gymharu â olwynion Canllaw 11T "
* Fersiwn dwyn Ceramig yn arbed mwy na 2.4 watt o rym gyfartaledd o gymharu â'r system symudol gwreiddiol
* Cawell ffibr carbon llawn
* 7075 aloi alwminiwm llawn CNC torri canllaw ysgafn olwyn a siafft pin
*Color: Anode red, enamel, blue, gold, green
*17TR is suitable for Shimano 6700/6770/6800/6870/9000/9070 Ultegra/DURA ACE
* Gan Ceramig Fersiwn Dur Di-staen Gan Hybrid Fersiwn Steel Gan Fersiwn
* Pwysau: 61.4g
* Ef Fersiwn Gan gadw ceramig yn 1.2 gram ysgafnach na'r fersiwn Gan dur
*Shifting speed increased by 20%-26% for Shimano systems.
*Support up to 11-28 cassettes, compatible with 11-30 and 11-34 with the help of an RD extender.
This is the fastest RD pulley system.
17TS & 17TR installation tips:
1, due to increased offset by the oversized pulley system, please make sure your RD and frame are aligned and calibrated correctly.
2, please check the length of your chain. Here is how to calculate, chain should be 10-20mm longer than the RD at 0 tension (shown as the picture below) when rests on the smallest chainring and smallest cog.
3, to lower the requirements for chain length and RD/frame alignment, we introduce the new 16T pulley system, 17TS and 17TR. Compare with 17T, the power saving would be lowered by about 0.2 watts but increasing chain stability and shifting speed.
Pam cymryd lle olwyn bwli derailleur
Yn gyntaf, gallai terfyn sefyllfa gwanwyn mandyllog addasu yn ôl tensiwn i raddau helaeth, yn gwella gwendid ymestyn wan gwreiddiol, ac yn gwneud i fyny ac i lawr tensiwn gadwyn rhwng Canllaw olwyn a cogiau yn llawer mwy yn ddigonol.
Yn ail, mae'r rhif cyswllt dant neu reoli rhif dannedd rhwng cadwyn a cogiau o 17T derailleur cefn yn fwy yn ystod y symud gêr, 'i jyst yn hoffi pinsied y canol a dwy ochr rhai ffyn, po fwyaf y lifer rheoli, cryfaf y pŵer rheolaeth.
Yn olaf, ar ôl ail-ddylunio gromlin cylchdro y cawell, mae'r pellter rhwng canllaw olwyn uchaf a'r cogiau yn cael ei wella.
camau gosod
1. Cefn dadelfeniad derailleur, cael gwared ar y cawell olwyn pwli gwreiddiol, fel y dangosir yn y ffigur (cawell olwyn bwli gwreiddiol wedi cael ei dynnu, dull gwared cyfeiriwch at ffigur Rhif 20)
2. Cadarnhewch y alwminiwm aloi cylch wyneb ochr wahanol.
3. Y prif gasged bollt.
4. Gosod y golchwr neilon i'r derailleur cefn.
5. Mowntio prif gasged bollt yn y bollt, a gwneud cais saim.
6. Cymerwch y cawell olwyn ffibr carbon pwli 17T, defnyddiwch Rhif 2 wrench hecs gwared aloi sgriw allan ar gefn y cawell olwyn pwli.
7. Tynnwch olwyn pwli uchaf.
8. Ar ôl cael gwared ar y olwyn pwli uchaf, gosod y bolltau canol ar y cefn.
9. Cyn gosod y prif bollt, bollt dylai'r gael ei iro yn llawn.
10. Gwthiwch y prif bollt yn llawn yn y waelod y cawell olwyn pwli.
11. Cadarnhewch yr wyneb rhigol ffoniwch aloi i'r prif bollt, ac wyneb rhigol wedi iro.
12. Cadarnhewch yr awyren ffoniwch aloi tuag allan, ac mae'r cylch aloi wedi iro.
13. Byddwch cystal â chadarnhau y twll mowntio gwanwyn yn derailleur cefn.
14. Mae'r pin gwanwyn aliniad gwanwyn twll mowntio mewn i'r derailleur cefn.
15. Cadarnhau y pin gwanwyn i mewn i waelod y twll lleoli gwanwyn.
16. Gosod y gwanwyn.
17. Cyd-fynd â'r pin gwanwyn gyda twll ar y cawell olwyn bwli
18. marcio yn 1 i 4 yn twll addasiad tensiwn, 'r ball mowntio cychwynnol yw twll 2. (tensiwn: 4> 3> 2> 1)
19. Mae'r cawell olwyn pwli wasgu llawn yn y derailleur cefn. cadarnhau'r prif aliniad bollt.
20. Rhif 4 wrench hecs i dynhau'r bollt brif i 4N.m.
21. Ail-osod y canllaw olwyn uchaf, mewnosoder y bolltau pwli uchaf, ond nid yn tynhau.
22. cylchdroi y cawell olwyn bwli i floc terfyn adlam derailleur cefn, gwasgwch y topupper bollt olwyn pwli allan, blocio y bloc terfyn.
23. Tynhau y bollt olwyn pwli uchaf.
24. Mae'r gosodiad wedi ei gwblhau.
According to test result, increase the rear derailleur pulley wheel size could significantly decrease the friction between the chain plates caused by polygon effects during chain bending, and reduce the resistance for saving rider’s cycling power.
The chain is composed of several short pieces with an inch long, we could see the chain as one inch long with around one hundred and ten section lines, due to small diameter of turning circle, when the lines pass through standard 11T pulley wheel, it needs a certain angle to turn the transferring direction of chain for about 180° through two wheels, after increasing the pulley wheel size, the chain turning angle are decreased, so the loss of friction is less correspondingly. The results shows that 17T is a good balance point between weight and decreasing the polygon effects, To increase the size blindly will lead to arc decreasing not obvious, together with weight and volume adding. Compared with common 11T pulley wheel, the friction loss caused by polygon effects of chain could be decreased about 60%.
Besides, under the same transferring speed of chain, the axis rotation speed of 17T is slower for saving the self friction loss during bearing rotation, smaller cycle could also reduce the resistance of each turn rotation. To upgrade this ceramic bearing saves more power loss.
Faster gear shifts. firstly, porous spring position limit could adjust back tension largely, improve the weakness of original weak stretch, and make the up and down chain tension between guide wheel and cogs much more adequately.
Yn ail, mae'r rhif cyswllt dant neu reoli rhif dannedd rhwng cadwyn a cogiau o 17T derailleur cefn yn fwy yn ystod y symud gêr, 'i jyst yn hoffi pinsied y canol a dwy ochr rhai ffyn, po fwyaf y lifer rheoli, cryfaf y pŵer rheolaeth.
Yn olaf, ar ôl ail-ddylunio gromlin cylchdro y cawell, mae'r pellter rhwng canllaw olwyn uchaf a'r cogiau yn cael ei wella.
And we should also tell customer that the compatibility of 11-28T cogs, the length of chain is within the range of 405-410mm standard road bike chain stay, suggest using more than 114 links, but not too short chain, or it might lead to too large back tension and enlarge the tooth tip resistance between chain and pulley wheels. (In case customer just has short chain, suggesting install it to lowest tension of spring mounting hole).
It can faster SHIMANO system up and down gear to improve 20%-26%. save 2.4 watts more.
