17TR koles Ceramic Ob karbonska vlakna Jockey jermenice gum Set Zadnje Menjalniki vodnik gum
Opis izdelka
* 17T Velika velikost vodilno kolo komplet sistem
*17T pulleys or16T pulleys
* Prihrani 60% odpornost verige torno primerjavi 11T vodilna kolesa "
* Keramični ležaj verzija prihrani več kot 2,4 vatov povprečna moč v primerjavi s prvotnim sistem spreminjajočo
* Kletka poln ogljikovih vlaken
* Celotno 7075 aluminijeve zlitine CNC razrez lahke vodilno kolo in gred zatič
*Color: Anode red, enamel, blue, gold, green
*17TR is suitable for Shimano 6700/6770/6800/6870/9000/9070 Ultegra/DURA ACE
* Ceramic Ob Izvedba iz nerjavečega jekla Hybrid Ob Različica Steel Ob Version
* Teža: 61.4g
* Je keramična izvedba Ob 1,2 gramov lažji od različice jeklo Bearing
*Shifting speed increased by 20%-26% for Shimano systems.
*Support up to 11-28 cassettes, compatible with 11-30 and 11-34 with the help of an RD extender.
This is the fastest RD pulley system.
17TS & 17TR installation tips:
1, due to increased offset by the oversized pulley system, please make sure your RD and frame are aligned and calibrated correctly.
2, please check the length of your chain. Here is how to calculate, chain should be 10-20mm longer than the RD at 0 tension (shown as the picture below) when rests on the smallest chainring and smallest cog.
3, to lower the requirements for chain length and RD/frame alignment, we introduce the new 16T pulley system, 17TS and 17TR. Compare with 17T, the power saving would be lowered by about 0.2 watts but increasing chain stability and shifting speed.
Zakaj zamenjati menjalnika jermenice kolo
Prvič, lahko porozna meja pomlad položaj nastavite nazaj napetost v veliki meri izboljša šibkost prvotnega šibko odsek, in da gor in dol napetosti verige med vodilnim kolesom in zob veliko bolj primerno.
Drugič, število stik zob ali kontrolna številka zob med verige in zobnikov zadnje menjalnika 17T več med prestavljanje, je tako kot ščepec na sredini in obe strani nekaterih palic, večja je ročica, močnejše nadzorno moč.
Na koncu, po preoblikovanju rotacijo krivulje kletko je, je razdalja med zgornjim vodilnim kolesom in zob izboljšalo.
Montaža koraki
1. Menjalnik zadaj dekompozicija, odstrani prvotni kletko škripec kolesa, kot je prikazano na sliki (bili odstranjeni prvotna škripec kolesni kletka Postopek odstranitve glejte ugotovimo No.20)
2. Potrdite aluminijeve zlitine obročni drugo stransko ploskev.
3. Glavni vijak tesnilo.
4. Namestite najlonski podložko na zadnjem menjalniku.
5. Vgradnja glavni vijak tesnilo na vijaku, in namažite.
6. Take kletko vlakno škripec kolo 17T ogljika, uporaba No. 2 inbus ključem odstranimo zlitina vijak ven na hrbtni strani kletke jermenico kolesa.
7. Odstranite zgornji kolut kolo.
8. Ko odstranite zgornjo jermenico kolo, namestite center vijake na hrbtni strani.
9. Pred namestitvijo glavni vijak, je treba vijak v celoti namazati.
10. popolnoma Push glavni sornik na dnu kletke jermenico kolesa.
11. Potrdite utora površino zlitina obročni v glavni sornik, in utor površina je mazanja.
12. Potrdite zlitina obročni ravnino navzven in zlitine obroč mazanja.
13. Potrdite vzmeti montažno luknjo v zadnjem menjalniku.
14. vzmetni zatič poravnavo vzmet pritrdilna luknja v zadnjem menjalniku EU.
15. Potrdi vzmetnega v spodnjem delu izvrtine vzmet pozicioniranja.
16. Namestitev vzmeti.
17. poravnano vzmetnega z luknjo na kletko jermenico kolesa
18. Označeno v 1 do 4, je napetost luknja prilagoditev, začetna pritrditev privzeto je luknja 2. (napetost: 4> 3> 2> 1)
19. kletko kolo škripec do konca pritisnjena v zadnjem menjalniku. potrjujejo glavno poravnavo vijak.
20. Ne 4 heks ključa zategniti glavni sornik do 4N.m.
21. Reset zgornjo vodilno kolo, vstavite škripcem vijake, vendar ne zaostrila.
22. Vrtenje kletko na škripec kolo na mejni blok zadnji menjalnik preobratu, pritisnite vijak škripec kolesa na topupper ven, blokiranje mejno blok.
23. Zategovanje zgornji vijak jermenice kolo.
24. Namestitev je končana.
According to test result, increase the rear derailleur pulley wheel size could significantly decrease the friction between the chain plates caused by polygon effects during chain bending, and reduce the resistance for saving rider’s cycling power.
The chain is composed of several short pieces with an inch long, we could see the chain as one inch long with around one hundred and ten section lines, due to small diameter of turning circle, when the lines pass through standard 11T pulley wheel, it needs a certain angle to turn the transferring direction of chain for about 180° through two wheels, after increasing the pulley wheel size, the chain turning angle are decreased, so the loss of friction is less correspondingly. The results shows that 17T is a good balance point between weight and decreasing the polygon effects, To increase the size blindly will lead to arc decreasing not obvious, together with weight and volume adding. Compared with common 11T pulley wheel, the friction loss caused by polygon effects of chain could be decreased about 60%.
Besides, under the same transferring speed of chain, the axis rotation speed of 17T is slower for saving the self friction loss during bearing rotation, smaller cycle could also reduce the resistance of each turn rotation. To upgrade this ceramic bearing saves more power loss.
Faster gear shifts. firstly, porous spring position limit could adjust back tension largely, improve the weakness of original weak stretch, and make the up and down chain tension between guide wheel and cogs much more adequately.
Drugič, število stik zob ali kontrolna številka zob med verige in zobnikov zadnje menjalnika 17T več med prestavljanje, je tako kot ščepec na sredini in obe strani nekaterih palic, večja je ročica, močnejše nadzorno moč.
Na koncu, po preoblikovanju rotacijo krivulje kletko je, je razdalja med zgornjim vodilnim kolesom in zob izboljšalo.
And we should also tell customer that the compatibility of 11-28T cogs, the length of chain is within the range of 405-410mm standard road bike chain stay, suggest using more than 114 links, but not too short chain, or it might lead to too large back tension and enlarge the tooth tip resistance between chain and pulley wheels. (In case customer just has short chain, suggesting install it to lowest tension of spring mounting hole).
It can faster SHIMANO system up and down gear to improve 20%-26%. save 2.4 watts more.
